background image

And that the following paragraphs of the harmonised standards have been applied.

Et que les paragraphes suivants les normes harmonisées ont été appliqués.

Und dass die folgenden Paragraphen der vereinheitlichten Normen Angewandt wurden.

E che sono stati applicati i seguenti paragraphi delle norme armonnizzate.

Y que se han aplicado los siguientes apartados de las normas armonizadas.

Aqu@ Scop HT SPLIT 12-6 / Aqu@ Scop HT SPLIT 14-7 / Aqu@ Scop HT SPLIT 18-9

MACHINERY DIRECTIVE 2006 / 42 / EEC

LOW VOLTAGE DIRECTIVE (DBT) 2006 / 95 / EEC

ELECTROMAGNETIC COMPATIBILITY DIRECTIVE 2004 / 108 / EEC

PRESSURISE EqUIPMENT DIRECTIVE (DESP) 97 / 23 / EEC

SUB-MODULE A CATEGORY I

DIRECTIVE MACHINES 2006 / 42 / C.E.E.

DIRECTIVE BASSE TENSION (DBT) 2006 / 95 / C.E.E.

DIRECTIVE COMPATIBILITE ELECTROMAGNETIqUE 2004 / 108 / C.E.E

DIRECTIVE DES EqUIPEMENTS SOUS PRESSION (DESP) 97 / 23 /C.E.E.

SOUS-MODULE A CATEGORIE I

RICHTLINIE MASCHINEN 2006 / 42 / EG

RICHTLINIE NIERDERSPANNUNG (DBT) 2006 / 95 / EG

RICHTLINIE ELEKTROMAGNETISHE VERTRÄGLICHKEIT 2004 / 108 / EG

RICHTLINIE FÜR AUSRÜSTUNGEN UNTER DRUCK (DESP) 97 / 23 / EG

UNTER MODUL A, KATEGORIE I

DIRETTIVA MACHINE 2006 / 42 / CEE

DIRETTIVA BASSA TENSIONE (DBT) 2006 / 95 / CEE

DIRETTIVA COMPATIBILITA ELETTROMAGNATICA 2004 / 108 / CEE

DIRETTIVA DEGLI IMPIANTI SOTTO PRESSIONE (DESP) 97 / 23 / CEE

SOTTOMODULO A, CATEGORIA I

DIRECTIVA MAqUIAS 2006 / 42 / CEE

DIRECTIVA BAJA TENSION (DBT) 2006 / 95 / CEE

DIRECTIVA COMPATIBILIDAD ELECTROMAGNETICA 2004 / 108 / CEE

DIRECTIVA DE LOS EqUIPOS A PRESION (DESP) 97 / 23 / CEE

BAJA MODULO A, CATEGORIA I

Déclaration CE de conformité

Nous déclarons sous notre responsabilité que les produits désignés dans la présente notice sont conformes aux dispositions des directives CEE énoncées 

ci- après et aux législations nationales les transposant.

EC Compliance declaration

Under our own responsibility, we declare that the product designated in this manual comply with the provisions of the EEC directives listed hereafter 

and with  the national legislation into which these directives have been transposed.

EG-Konformitätserklärung

Wir erklarën in eigener  Verantwortung, das die in der vorliegenden Beschreibung angegebenen Produkte den Bestimungen der nachstehend  

erwähnten EG-Richtlinien und den nationalen Gesetzesvorschriffen entsprechen, in denen diese Richtinien umgesetz sind.

Dichiarazione CE  di conformità

Dichiariamo, assurmendone la responsasabilità, che i prodotti descritti nel presente manuale sono conformi alle disposizioni delle direttive CEE di cui 

sott e alle lagislazionni nazionali che li recepiscono

Declaramos, bajo nuestra responsabilidad, que los productos designados en este manual son conformes a las disposiciones de las directivas CEE 

enunuciadas a continuacion, asi como a las legislaciones nacionales que las contemplan.

Declaración CE  de conformidad

 EN 378-2:2002 

 

EN 61000-6-3:2007 

 EN 61000-6-1:2007 

 

EN 61000-3-2:2006 

 EN 61000-3-3:1995 + A1 2001 + A2 2005 

 

EN 60 335-2-21 

 EN 60 335-1 

 

EN 60 335-2-40

A Tillières sur Avre
27570 - FRANCE
Le: 11/01/2012
Sébastien Blard
Quality Manager
AIRWELL Industrie France

Содержание Aqu@Scop HT SPLIT 12-6





















































































Отзывы: