Airwell Aqu@Scop HT SPLIT 12-6 Скачать руководство пользователя

Страница: 54 / 84

Alarm description

SCOP

PLIT

action

Alarm cancellation

Time delay

Possible cause(s)

Recommended action(s)

INF36

--Information-- Back

up heater Boiler/

Electric heater

enabled

Information

Stop backup mode

None

Activation of the EMH digital input

of the controller or backup mode

through the display for boiler relief

AL39

ater pressure <

0.5bar in the heating

circuit

Information

Pressure > 1 bar for

5s.

10 s

Insufficient water pressure in the

Heating circuit.

Add water to the heating circuit. Check

proper expansion tank operation.

Check for leaks on the Heating network.

AL40

No communication

with the outdoor unit

Complete

thermodynamic function

stoppage

Manual and Com OK

for 22s.

22s

Incorrect wiring

Check bus connections at both ends.

Communication bus cable cut.

Check the condition of the bus cable

Unshielded cable.

Install shielded cable.

Outdoor unit not auto

-detected.

Check the wiring of the Outdoor unit

probes.

AL41

Aqu@

Split

unit not recognized on

the communication

bus

Information

Automatic

None

Probes B1 to B4, B8 and B9

partially or totally disconnected on

the unit in question.

Check the probe values on the display

and check the probe connections.

AL42

Indoor/outdoor units

software versions

incompatible

Complete

thermodynamic function

stoppage

Power supply cut.

None

Different versions for Indoor and

Outdoor units.

Update the programme for both units.

AL43

Aqu@

Split

model detected Split

or Monobloc

Complete stoppage.

Power supply cut.

None

Probes B1 to B4, B8 and B9

partially or totally disconnected on

the unit in question.

Check the probe values on the display

and check the probe connections.

AL44

Aqu@

Split

model modified for

the indoor unit

Information

None

Probes B1 to B4, B8 and B9

partially or totally disconnected on

the unit in question

=> incorrect model detection

Check the probe values on the display

and check the probe connections.

µPC replaced by that of another

Aqu@

Split

(Split

Indoor/Outdoor /Monobloc)

Confirm once the situation is understood.

Programme taken from another

Aqu@

Split

(Split

Indoor/Outdoor/Monobloc)

Содержание Aqu@Scop HT SPLIT 12-6





















































































Результаты поиска

Содержание Aqu@Scop HT SPLIT 12-6

Отзывы:

Похожие инструкции для Aqu@Scop HT SPLIT 12-6

Бренды по названию

Популярные бренды

Airwell Aqu@Scop HT SPLIT 12-6, Инструкция по установке

Результаты поиска

Содержание Aqu@Scop HT SPLIT 12-6

Отзывы:

Похожие инструкции для Aqu@Scop HT SPLIT 12-6

Бренды по названию

Популярные бренды