manualshive.com logo in svg

Airspan MicroMAX, Руководство по установке оборудования и инструкция пользователя

Поделиться
Скачать
Airspan MicroMAX Скачать руководство пользователя страница 49

                                

MicroMAX Hardware Installation User Guide

 

 

 

 
Page 49 

Commercial in Confidence 

UWB-D00068 Rev J 

 

 

 

Figure 32 - strain relief 

9.2  Wall-Mounting the BSR (Optional) 

 

 

Note:

 The standard BSR kit provides pole-mounting brackets. If you want to 

wall-mount the MicroMAX BSR contact your Airspan distributor for pricing 
and ordering of wall-mounting brackets. 

 

 

Note:

 A minimum of 3 meter separation is required between MicroMAX and 

existing customer radio equipment. 

 

 

Note:

 A minimum of 1 meter separation should be maintained between 

synchronized MicroMAXs (see figure below). 

 

The figure below illustrates the minimum separation between synchronized MicroMAX's : 

 

Figure 33 - mount separation 

MicroMAX wall mounting consists of two main stages: 

¾

  Attaching the mounting bracket to the MicroMAX's mounting holes 

¾

  Attaching the mounting bracket (already attached to the MicroMAX) to the wall (or pole) 

To wall mount the MicroMAX: 

1.  Position the unassembled mounting bracket on the mounting surface (e.g. wall), and then 

use a pencil to mark the position of the four mounting holes. Ensure that the distance 
between the hole centers are 120 mm (height) and 60 mm (width), as displayed in the figure 
below showing the MicroMAX's fixing dimensions. 

Содержание MicroMAX





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды