Airspan FlexNET ASN-700 Скачать руководство пользователя страница 9

Страница: 9 / 76

605-0001-801 FlexNET Link Products

INTRODUCTION

This guide contains information on how to operate and manage the ASN-700/800 products.

PACKAGE CONTENTS

The ASN-700/800 package contains the following items:

ASN-700/800 product

Mounting kit with downtilt

One weather proof power connector kit

One weather proof RJ-45 connector kit

Outdoor power supply unit PSU-3

Factory default tool

Mounting instruction

Documentation CD-ROM

PHYSICAL INTERFACES AND DESCRIPTION

Key features of the ASN-700/800 are:

Aluminum enclosure supports outdoor installation

Industrial temperature rating (-40…+55

Two external antenna connectors (ASN-800 only)

One (ASN-700) or two (ASN-800) 10/100 Base TX Ethernet ports

Activity indication LED

Detachable power connection with RS-485 connection for remote management

Antenna

The ASN-700 is delivered with an integrated 5 GHz 23dBi patch antenna. Integrated link

antenna element is covered with a white radome to protect it. The ASN-800 does not have an

integrated antenna.

Aluminum enclosure

The base station unit uses an aluminum enclosure that supports outdoor operating

environments and supports an industrial temperature operating range.

Connectors

All connectors are located on the bottom of the housing. Depending on your product version the

number of Ethernet and antenna connectors may differ from the overview example presented

here.

Содержание FlexNET ASN-700













































































Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды

Airspan FlexNET ASN-700, Руководство пользователя

Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды