Airspan FlexNET ASN-700 Скачать руководство пользователя страница 67

Страница: 67 / 76

605-0001-801 FlexNET Link Products

APPENDIX 8: CONFIGURING A NETWORK

In the following, an example on how to configure a small network is provided.

1. Install the ControlNET server.

2. Login to the server’s web interface via eth1 using the IP address 192.168.1.254/24.

3. Click the Base stations link on the Navigation menu. Click Add new base station.

4. Enter the following information in the corresponding fields. Name: bs1, IP: 192.168.1.1,

RoamNET range: 172.16.0.0/24, RoamNET passwd: default, SNMP Community: public

5. Press Save.

6. Click Add new base station.

7. Enter the following information in the corresponding fields. Name: bs2, IP: 192.168.1.2,

RoamNET range: 172.16.1.0/24, RoamNET passwd: default, SNMP Community: public

8. Press Save.

9. Click the Bandwidth management link on the Navigation menu. Click Add new

bandwidth limit entry.

10. Enter the following values: To subscriber: 1024, From subscriber: 512

11. Press Create.

12. Click the Guests preferences link on the Navigation menu.

13. Click Enabled. Enter the following information in the corresponding fields. Network:

192.168.255.0/24, IP range: 192.168.255.0/24, Select bandwidth limit, Domain:

test.network, Gateway: 192.168.255.1, DNS 1 and 2: your DNS server names (can be the
same), Lease time: 1d, Comment: Guests class.

14. Press Save.

15. Click the Routes link on the Navigation menu. Click Add routes.

16. Enter the following values. Network: 172.16.0.0/24, Gateway: 192.168.1.1, Comment:

RoamNET range for bs1

17. Click the Routes link on the Navigation menu. Click Add routes.

18. Enter the following values. Network: 172.16.1.0/24, Gateway: 192.168.1.2, Comment:

RoamNET range for bs2

19. Press Apply routes.

Содержание FlexNET ASN-700













































































Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды

Airspan FlexNET ASN-700, Руководство пользователя

Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды