Airspan FlexNET ASN-700 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 76

background image

605-0001-801 FlexNET Link Products

OK

Clicking the OK button after editing any configuration page will save the new settings to

the ASN-700/800. The new settings will not be enabled until Commit Settings button is
clicked (see below).

Commit Settings

Click the Commit Settings button to enable saved settings to persist after reboot of the

ASN-700/800. The currently saved settings will be written into the non-volatile memory of

the ASN-700/800 and will be read at each reboot.

Note: To make permanent changes to the configuration of the ASN-700/800:

1.

Navigate to the appropriate configuration page and enter new settings.

2.

Click the OK button to accept and apply your changes.

3.

Using the menu, navigate to any further pages you wish to configure and repeat

steps (1) and (2).

4.

When you are satisfied with the configuration of the device, click the Commit
Settings button to permanently record your changes.

14

«
...
18
19
20
21
22
...
»

Содержание FlexNET ASN-700













































































Отзывы:

Нет отзывов

Похожие инструкции для FlexNET ASN-700

ShareCenter DNS-320L

Бренд: D-Link Страницы: 4

MediaStream ConnectPlus 1000

Бренд: Avid Technology Страницы: 74

Бренд: NETGEAR Страницы: 2

Бренд: Usr Страницы: 2

totalstorage 200

Бренд: IBM Страницы: 152

Бренд: Tripp Lite Страницы: 3

Бренд: UfiSpace Страницы: 35

AceroDURO 100/S100

Бренд: CNC-Step Страницы: 86

Бренд: KYLAND Technology Страницы: 24

Бренд: Goobay Страницы: 20

Gen3 Ethernet Module

Бренд: NCD Страницы: 18

Бренд: 3Com Страницы: 63

Бренд: Martin Страницы: 41

IE-SW-AL18M-16TX-2GC

Бренд: Weidmüller Страницы: 2

OmniSwitch 6624

Бренд: Alcatel Страницы: 546

Бренд: Intercel Страницы: 17

IPSec VPN Client Zyxel ZyWall 10

Бренд: TheGreenBow Страницы: 12

Бренд: Fibrain Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды