Airspan FlexNET ASN-700 Скачать руководство пользователя страница 11

Страница: 11 / 76

605-0001-801 FlexNET Link Products

INSTALLATION INSTRUCTIONS

The ASN-700/800 is designed for outdoor installation environment, on a tower, a tall building or

an antenna mast.

A professional installer must install the base station and the antennas. The installer should also

be familiar with network structures, terms, and concepts.

Installation direction

Connectors must always be downwards in outdoor installations. In indoor installations (e.g.

warehouses etc.) direction can be freely selected if the integrated antenna is not used.

Antenna mast installation

The following figures present installation in an antenna mast pipe; antenna pipe diameters

45…60mm (approx. 1 3/4…2 1/3 inches).

Содержание FlexNET ASN-700













































































Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды

Airspan FlexNET ASN-700, Руководство пользователя

Результаты поиска

Содержание FlexNET ASN-700

Отзывы:

Похожие инструкции для FlexNET ASN-700

Бренды по названию

Популярные бренды