Airspan AS MAX EasyST 4.9 Скачать руководство пользователя страница 34

Страница: 34 / 50

605-0000-703 EasyST 49 Installation User Guide-Rev D

Interfaces:

  10/100BaseT (8-pin RJ-45)
  DC power (DC power jack)
  RF: Clip-on antenna (MCX

connector and 6-pin Antenna

Controller)

SIM slot (planned for future)
Plug-in expansion module through

30-pin IDC socket for the

following interfaces:

802.11 Wi-Fi -- planned for future

LAN switch -- planned for future

VoIP and Battery Backup --

planned for future

Power

requirements:

6 VDC, 4A, supplied by AC/DC power

adapter plugged into a standard electrical

wall outlet (110/240 VAC, 50/60 Hz)

Dimensions:

With clip-on antenna: 130 x 145 x

145 mm (5.12 x 5.7 x 5.7 inches)

Without clip-on antenna: 30 x 145

x 145 mm (1.18 x 5.7 x 5.7

inches)

Mechanical

and

Electrical

Weight:

With clip-on antenna: 0.426 kg

(approximate)

Without clip-on antenna: 0.3 kg

(approximate)

Power Adapter Specifications

The specifications of the AC/DC power adapter are listed in the table below:

Category

Parameter

Value

Input voltage

90 to 264 VAC

Input frequency

47 to 63 Hz

Input inrush current

30 A at 115 VAC
60 A at 230 VAC

Input

Earth leakage

0.4 mA max. @ 115 VAC
0.8 mA max. @ 230 VAC

Output rating

6V / 4A

Output voltage accuracy

2% max.

Max. output power

24W

Line regulation

1% max.

Output

Load regulation (full to half

load)

6 ˜6.5V

Содержание AS MAX EasyST 4.9



















































Результаты поиска

Содержание AS MAX EasyST 4.9

Отзывы:

Бренды по названию

Популярные бренды

Airspan AS MAX EasyST 4.9, Руководство по установке оборудования

Результаты поиска

Содержание AS MAX EasyST 4.9

Отзывы:

Бренды по названию

Популярные бренды