manualshive.com logo in svg

Airspan AirSynergy3, Руководство по установке

Поделиться
Скачать
Airspan AirSynergy3 Скачать руководство пользователя страница 58

                                 

AirSynergy3 Equipment Installation Guide

 

Page 58 |                                     Commercial in Confidence                                           SYN-UG-018 

 

11  Appendix F 

– FCC Requirements 

Airsynergy basestation, FCC ID: O2J-235AS, operating in the 
2305-2320 and 2345-2360 MHz WCS Bands. 

 

Federal Communications Rules for operation in USA 

The  correct  setting  of  the  following  Base  Station parameters  in  Netspan,  are  critical  to  
the correct operation of equipment in compliance with the rules detailed in 47CFR27subpart 
C: 

 

Transmit Power 

 

Transmit Frequency 

 

Channel Bandwidth 

Any attempt to alter these parameters outside those permitted by the Netspan software or the 
operator license could be a violation of that license 

 

Transmit Power / Tune-up 

Transmit power is set using the Netspan management software during install /commissioning. 

The unit may transmit with a power of up to 30dBm at each antenna port when connected to 
cross polarised antenna with maximum gain of 18dBi 

 

Airsynergy basestation, FCC ID: O2J-265AS, operating in the 
2572-2614 MHz band. 

 

Federal Communications Rules for operation in USA 

The  correct  setting  of  the  following  Base  Station parameters  in  Netspan,  are  critical  to  
the correct operation of equipment in compliance with the rules detailed in 47CFR27subpart 
C: 

 

Transmit Power 

 

Transmit Frequency 

 

Channel Bandwidth 

Any attempt to alter these parameters outside those permitted by the Netspan software or the 
operator license could be a violation of that license 

Transmit Power / Tune-up 

Transmit power is set using the Netspan management software during install /commissioning. 

The unit may transmit with a power of up to 30dBm at each antenna port when connected to 
cross polarised antenna with maximum gain of 18dBi 

 

Содержание AirSynergy3


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды