manualshive.com logo in svg

Airspan AirSynergy3, Руководство по установке

Поделиться
Скачать
Airspan AirSynergy3 Скачать руководство пользователя страница 33

                                 

AirSynergy3 Equipment Installation Guide

 

Page 33 |                                     Commercial in Confidence                                           SYN-UG-018 

 

5  Power System Connection 

 

Caution:

 Hazardous voltage!

  Before working, ensure that the power is removed 

from the power connection cables.  When the system is powered on, 

do not 

touch the power terminals

. 

 

Tools Required: 

The tools required for the connection of the PSU are:  knife, 

small flat blade screw driver (electrical insulated shaft recommended), medium 
cross-head screw driver, pliers, small side cutters, tweezers (or fine blade long 
nose pliers)  

 

Figure 40 – Tools required to connect the PSU 

 

5.1  Run cables from the PSU to the AirSynergy  

 

5.1.1 The drop cable installation. If the drop cable is to be passed through glands and/or down the 
centre of a lamp post or other structure, the drop cable can be cut leaving sufficient length for ease of 
termination

. (The typical cable supplied is 30m in length and other length options are available)

 

With the power supply placed at the selected installation location, trim the cable  to the length for neat 
installation while allowing sufficient length to strip and prepare the cable ends.  

 

 

 
Note

:  

It is good practice to label both ends of the drop cable to identify which 

AirSynergy unit it is connected to. This is especially important where multiple 
AirSynergy units are installed on the same pole/tower. 

 

  

 
Note:  

It is good practice to leave a spare loop of drop cable  (approximately 0.5m 

of cable). This will allow for ease of wiring to the power supply and will allow the 
cable to be re-terminated if necessary in the future.

 

 

Содержание AirSynergy3


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды