manualshive.com logo in svg

Airspan AirSynergy3, Руководство по установке

Поделиться
Скачать
Airspan AirSynergy3 Скачать руководство пользователя страница 25

                                 

AirSynergy3 Equipment Installation Guide

 

Page 25 |                                     Commercial in Confidence                                           SYN-UG-018 

 

3.3   Fit GPS Antenna to AirSynergy 

  

 

Note:

 AirSynergy units without a factory fitted Switched Beam Antenna all require 

a GPS antenna which comes in a kit with a mounting bracket and a 25cm cable. 
A prime consideration for a GPS antenna is a clear view of the sky, preferably 
360 degrees 

 

3.3.1  Fit the GPS antenna to the mounting bracket supplied in the GPS antenna mounting kit. The 
large back nut should be tightened with a pipe wrench. Take care not to over tighten on the plastic 
threads. 

 

Figure 25 –Fitting the GPS antenna to the mounting bracket 

 

3.3.2  Fit the short TNC to TNC cable from the GPS antenna to the TNC connector on the top of the 
AirSynergy  

Note: For extreme weather conditions weather-proofing of the TNC connections is recommended. 
This is done with a layer of self-amalgamating tape followed by an over layer of PVC tape. The 
weather-proofing is best done at this stage to give easier access to the connections 

 

Figure 26 –GPS antenna cable connected 

3.3.3  Fit the GPS antenna assembly to the body of the AirSynergy using the single M6 screw and 
lock washer provided in the kit. There is a threaded hole at the top corner of the AirSynergy unit for 
this purpose. The TNC to TNC cable loop can be gently positioned behind the front mount antenna (or 

Содержание AirSynergy3


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды