manualshive.com logo in svg

Airspan AirSynergy3, Руководство по установке

Поделиться
Скачать
Airspan AirSynergy3 Скачать руководство пользователя страница 12

                                 

AirSynergy3 Equipment Installation Guide

 

Page 12 |                                     Commercial in Confidence                                           SYN-UG-018 

 

2.1.2  Switched Beam Antenna Arrangement 

A switched beam antenna version (factory built option) with built in GPS antenna allows for flexible 
iBridge backhaul functionality where the strongest signal from any direction is automatically selected. 
The same antenna can also be configured in omni mode for the support of access. 

 

Figure 3

– AirSynergy with Switched Beam Antenna 

2.1.3  Dual radio unit arrangement 

AirSynergy units may also be supplied in a dual radio arrangement. 

Note: Various antenna options 

can be selected for each AirSynergy to perform the required combination of backhaul and access 
functionality. An extended sun-shield is also available for this format. 

 

Figure 4 

– AirSynergy dual radio configuration 

Содержание AirSynergy3


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды