manualshive.com logo in svg

Airspan AirHarmony-4400, Руководство по установке

Поделиться
Скачать
Airspan AirHarmony-4400 Скачать руководство пользователя страница 9

AirHarmony-4400 (External Cavity Filters) Installation Guide 

UGD-D01186 

Airspan Commercial and Internal Use 

3 

 

Warnings and Cautions 

Human Exposure to Radio Frequencies 

The AirHarmony-4400 antennas should be operated from a minimum safe distance of 4.6m  

Radio Interference 

The AirHarmony generates, uses, and can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment on and off, the technician is encouraged to try to correct the 
interference by performing one or more of the following measures: 

 

Re-orientate or relocate the unit  

 

Increase separation between the units and/or End Devices 

 

Connect the equipment to a circuit different from that to which the power source is 
connected 

Modifications 

Any changes and modifications to this device that are not expressly approved by Airspan Networks 
may void the user's authority to operate the equipment. 

General 

 

Only qualified personnel should be allowed to install, replace, and service the equipment. 

 

The device cannot be sold retail, to the general public or by mail order. It must be sold to 
operators. 

 

Installation must be controlled. 

 

Installation must be performed by licensed professionals. 

 

Installation requires special training. The AirHarmony-4400 should be installed ONLY by 
experienced installation professionals who are familiar with local building and safety codes 
and, wherever applicable, are licensed by the appropriate government regulatory 
authorities. Failure to do so may void Airspan's product warranty and may expose the end 
user or the service provider to legal and financial liabilities. Airspan and its resellers or 
distributors are not liable for injury, damage or violation of regulations associated with the 
installation of outdoor units or antennas. 

 

The device is to be installed in a Restricted Access Location. 

 

Surge Arrestors and Transient Voltage Surge Suppressors installed external to the ITE are 
required to comply with the appropriate CEC/NEC requirements. 

Général 

 

Seul le personnel qualifié peut être autorisé pour installer ou remplacer l’équipement ainsi 
qu’effectuer les opérations de maintenance pour cet équipement. 

 

L’équipement ne peut pas être vendu en grande distribution ou par commande via email à 
destination du public. Il doit être vendu aux opérateurs de télécommunications. 

 

Son installation doit être contrôlée. 

 

Son Installation doit être effectuée par des professionnels autorises. 

Содержание AirHarmony-4400































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды