Airspan AirHarmony 4000 DC Скачать руководство пользователя страница 49

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide 

UGD-D01123

 

Airspan Commercial and Internal Use 

43 

B

 

Abbreviations 

Term  

Expansion 

3GPP 

3rd Generation Partnership Project, responsible for LTE 

ABS 

Almost Blank Subframes 

ACS

 

Adjacent Channel Selectivity is a measurement of a receiver's ability to process a desired 
signal while rejecting a strong signal in an adjacent frequency channel. ACS is defined as the 
ratio of the receiver filter attenuation on the assigned channel frequency to the receiver 
filter attenuation on the adjacent channel frequency.

 

AWGN 

Additive White Gaussian Noise is a channel model in which the only impairment to 
communication is a linear addition of white noise with a constant spectral density and a 
Gaussian distribution of amplitude. 

BER 

Bit Error Rate 

CN 

Core Network 

CP 

Cyclic Prefix 

CTC 

Convolution Turbo Code is a high-performance forward error correction (FEC) code 

dB 

Decibel. A logarithmic unit used to describe a ratio (such as power ratio in radio 
telecommunications) 

dBm 

An abbreviation for the power ratio in decibels (dB) of the measured power referenced to 
on

milliwatt

 (mW). It is used as a convenient measure of absolute power because of its 

capability to express both very large and very small values in a short form. 

eNodeB 

Evolved Node B, is the element i

E-UTRA

N o

LTE

. 

ESP 

Encapsulating Security Payloads (ESP) provide confidentiality, data-origin authentication, 
connectionless integrity, an anti-replay service (a form of partial sequence integrity), and 
limited traffic-flow confidentiality 

E-UTRAN 

Evolved UMTS Terrestrial Radio Access Network, is the air interface of 3GPP's Long Term 
Evolution. 

EVM/RCE 

The Error Vector Magnitude or EVM (sometimes also called Receive Constellation Error or 
RCE) is a measure used to quantify the performance of a digital radio transmitter or receiver. 
It is measured in dB or percentage (%) 

 the lower the better. 

FDD 

Frequency-Division Duplexing. A transceiver mode where the transmitter and receiver 
operate at different carrier frequencies. 

GNSS 

Global Navigation Satellite System is a term used to describe a satellite navigation system 
with global coverage. There are currently two fully operational GNSSs 

 the US GPS and the 

Russian GLONASS 

GTP-U 

GPRS Tunneling Protocol for User data is a relatively simple IP based tunneling protocol 
which permits many tunnels between each set of end points 

HPBW 

Half Power BandWidth is the angular separation in an antenna, in which the magnitude of 
the radiation pattern decreases by 50% (or -3 dB) from the peak of the main beam 

ICS 

In-

ha el sele ti it  is a  easu e of the  e ei e ’s a ilit  to  e e

ive a wanted signal at its 

assigned Resource Block locations in the presence of an interfering signal 

IPSec 

Internet Protocol Security is a protocol suite for securing Internet Protocol (IP) 
communications by authenticating and encrypting each IP packet of a communication 
session 

LED 

Light Emitting Diode 

LTE 

Long Term Evolution 

MAC 

Medium Access Controller 

 responsible for several functions such Error Correction, Packet 

De Multiple i g, et …

 

MBSFN 

Multicast-Broadcast Single Frequency Network is an LTE feature designed to deliver services 
such as Mobile TV using the LTE infrastructure, and is expected to be a competitor to DVB-H-
based TV broadcast 

Содержание AirHarmony 4000 DC



















































Отзывы: