manualshive.com logo in svg

Airspan AirHarmony 4000 DC, Руководство по установке

Поделиться
Скачать
Airspan AirHarmony 4000 DC Скачать руководство пользователя страница 35

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide 

UGD-D01123

 

Airspan Commercial and Internal Use 

29 

 

1.

 

Select the location on the pole to mount the AirHarmony-4000. You can attach the 
AirHarmony-4000 to any pole from 1-7/8 to 16 inches (47.6 to 406.4 mm) in diameter.  

2.

 

Insert the clamp straps through the slots in the mounting plate passing them through 
the pole clamps. 

3.

 

Insert the clamp bands by passing them through the slots in the mounting plate, in four 
(4) places. 

Note:

 The clamp bands are not supplied by Airspan and are the responsibility of the 

installer. Clamp bands should not be wider than 15.5 mm in order to fit in the slots on 
the mounting plate. 

 

4.

 

Tighten the clamp bands with large flat screwdriver. 

 

Figure 11: Mounting plate mounted 

 

 

4.2.3

 

Mounting on a Wall 

The following images show the wall mount assembly. 

Caution:

 Take care to install the Pole/Wall mounting plate in the correct orientation. 

Verify that the mounting pins are facing upwards as shown below. 

 

1.

 

Position mounting plate against the wall with mounting pins facing up. Be sure to 
position the wall mounting plate 

straight with 

level mounting 

to ensure the unit sits 

evenly.

 

2.

 

Mark the wall through the holes on the wall mount at the required height. 

Содержание AirHarmony 4000 DC



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды