manualshive.com logo in svg

Airspan AirHarmony 4000 DC, Руководство по установке

Поделиться
Скачать
Airspan AirHarmony 4000 DC Скачать руководство пользователя страница 33

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide 

UGD-D01123

 

Airspan Commercial and Internal Use 

27 

3.

 

Drill a minimum 7/16

 hole to 

accept the 3/8-16 threaded rod. 

4.

 

Thread the 3/8-16 threaded rod into the provided clinch-nut attached on the Pole/Wall 
mounting plate. 

5.

 

Holding the mounting plate (with the attached threaded rod) pass the 3/8-16 threaded rod 
through the drilled hole in the pole. 

6.

 

Install on the exposed thread that protrudes from pole a flat washer, split washer, and 

the  a 3/

-16 hex nut and tighten. 

7.

 

Insert the clamp bands by passing them through the slots in the mounting plate, in three 
(3) places. 

Note:

 The clamp bands are not supplied by Airspan and are the responsibility of the 

installer. Clamp bands should not be wider than 15.5 mm in order to fit in the slots on 
the mounting plate. 

 

8.

 

Tighten the clamp bands with large flat screwdriver. 

 

Figure 8: Mounting plate on pole 

 

 

 

 

Содержание AirHarmony 4000 DC



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды