manualshive.com logo in svg

Airspan AirHarmony-1000, Руководство по установке

Поделиться
Скачать
Airspan AirHarmony-1000 Скачать руководство пользователя страница 46

AirHarmony-1000 Installation Guide  

UGD-D01006

 

Airspan Commercial and Internal Use 

 

39 

 

6  Cable Connections 

Hazardous voltage!

  Before working, ensure that the power is removed from the power 

connection cables.  When the system is powered on, 

do not touch the power 

terminals

. 

6.1 Connecting the AC/DC Power Converter to 

AirHarmony-1000 

The DC Connector comes pre-assembled on the AC/DC Converter, as shown below: 

 

Figure 32: AC/DC Converter with DC power connector 

  

 

6.1.1 Power Cable Preparation 

The Power cable is connected to the AirHarmony-1000 using a Gland connector assembled on the 
bottom panel of the unit. 

1.  Remove the connector by unscrewing the body from the AirHarmony-1000, using the Gland 

wrench. 

2.  Pass the pre-assembled connector through the tail nut, gland seal, body and rubber seal of 

the connector casing as shown below. Do not tighten the tail nut. 

 

Figure 33: DC Power connector pre-assembled on converter 

 

 

Note

 The connector is attached inside the weather protected area of the enclosure and 

is not subjected to water/moisture therefore the use of 

die-electric gels is not required.

 

 

3.  Connect the DC power cable connector to the female connector outlet inside the unit. 

 

 

Содержание AirHarmony-1000































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды