Airspan AirHarmony-1000 Скачать руководство пользователя страница 14

Страница: 14 / 62

AirHarmony-1000 Installation Guide

UGD-D01006

Airspan Commercial and Internal Use

Maximum Output TX Power

Table 1: AirHarmony-1000 FCC Maximum Output TX Power

Frequency Band

FCC
TX EIRP

Antenna Gain

2300-2400 MHz

TBDdBm

TBDdBM

12dBi

2496-2 690

MHz

39.86dBm

57.86dBm

18dBi

Table 2: AirHarmony-1000 ETSI Maximum Output TX Power

Frequency Band

ETSI
TX EIRP

Antenna Gain

2300-2400 MHz

40dBm

52dBm

12dBi

2496-2 690

MHz

40dBm

58dBm

18dBi

Caution:

Do not set maximum output TX power to higher than local regulations.

Power Consumption

AirHarmony-1000 has a Max nominal power consumption of 130W. AirHarmony-1000 power
consumption is described in the following table:

Table 3: Power Consumption

Duplex

Tx Power at RF
Port (dBm)

Nominal Power
Consumption (W)

Power Supply Requirement (W)

FDD

TBD

TDD

156

200

Antenna System

The following antennas are designed specifically for AirHarmony-1000 deployments. Externally
mounted antennas are available for use as well (pending), but are specified separately.

Note:

For a list of compatible external antennas, please contact your nearest Airspan sales

representative.

Front Mounted Sector Antenna

The front mounted sector antenna is a cross polarized fixed antenna which mounts on the front of the
unit in place of the sun-shield.

Содержание AirHarmony-1000































































Результаты поиска

Содержание AirHarmony-1000

Отзывы:

Бренды по названию

Популярные бренды

Airspan AirHarmony-1000, Руководство по установке

Результаты поиска

Содержание AirHarmony-1000

Отзывы:

Бренды по названию

Популярные бренды