manualshive.com logo in svg

Airspan Air4G, Руководство по установке, Страница: 9 / 73

Поделиться
Скачать
Airspan Air4G Скачать руководство пользователя страница 9

 

Air4G Installation Guide

 

 

 

 
Page 9 

Commercial in Confidence 

UGD-D00229 Rev B 

 Warnings and Cautions 

Human Exposure to Radio Frequencies 

The Air4G antennas should be installed and operated from a minimum distance of 2.4 meters (for 
5.x, 3.x, 0707, 0808 and 1.x) or 3.4 meters (for 2.x) from your body.  

Radio Interference 

This Air4G generates, uses, and can radiate radio frequency energy and, if not installed and used 
in accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment on and off, the technician is encouraged to try to correct the 
interference by performing one or more of the following measures: 

  Re-orientate or relocate the antenna  

  Increase separation between the BSs and/or End Device 

  Connect the equipment to an outlet on a circuit different from that to which the power 

source is connected 

Avoiding Radio Interference  

Ensure a minimum of 1-meter separation between co-located antennas of Air4G units. 

Modifications 

Any changes and modifications to this device that are not expressly approved by Airspan 
Networks may void the user's authority to operate the equipment. 

General 

  Only qualified personnel should be allowed to install, replace, and service the 

equipment. 

  The device cannot be sold retail, to the general public or by mail order. It must be 

sold to operators. 

  Installation must be controlled. 

  Installation must be performed by licensed professionals. 

  Installation requires special training. The Air4G radio and antenna should be installed 

ONLY by experienced installation professionals who are familiar with local building 
and safety codes and, wherever applicable, are licensed by the appropriate 
government regulatory authorities. Failure to do so may void Airspan's product 
warranty and may expose the end user or the service provider to legal and financial 
liabilities. Airspan and its resellers or distributors are not liable for injury, damage or 
violation of regulations associated with the installation of outdoor units or antennas. 

Safety  

1.  Read this guide and follow all operating and safety instructions. 

2.  Keep all product information for future reference. 

3.  This product is supplied with a grounding power plug. Do not defeat this important safety 

feature. 

4. 

Warning

: High voltages exist inside the product - do not remove the lid or base: No user 

serviceable parts inside. 

5.  Position the power cord to avoid possible damage; do not overload wall outlets. 

6.  Do not place this product on or near a direct heat source, and avoid placing objects on 

the terminal. 

Содержание Air4G










































































Отзывы:

Нет отзывов