Airmar TRIDUCER P66 Скачать руководство пользователя страница 1

17

-2

47

-0

3 re

v.

 0

3

04

/10

max. 

no

 speed sensor:

191mm (7-1/2") 

Transom-mount Depth Transducer 
           

              

or TRIDUCER

®

 Multisensor

with Integral Release Bracket

Model P66

U. S. Patents: 5,606,253; 5,719,824

Applications

• Not recommended for boats with large or twin-screw inboard 

engine(s)

• Not recommended for stepped hulls
• Good operation up to 44kn (50MPH)
• Vertically orients sound beam on hull with deadrise angle up to 30°
• Adjusts to transom angles from 2

°

–22

°

• Bracket protects sensor from frontal impact only

Tools & Materials

Safety goggles
Dust mask
Scissors
Masking tape
Electric drill
Drill bits:

Bracket holes

4mm, #23, 

or

 9/64"

Transom hole (optional)

21mm 

or

 13/16"

Cable clamp holes

3mm 

or

 1/8"

Angle finder
Marine sealant
Screwdrivers
Straight edge
Pencil
Grommet(s) (some installations)
Cable ties
Water-based anti-fouling paint (

mandatory in salt water

)

75 mm (3")

minimum beyond

swing radius 

 Figure 1. Headroom required on a stepped transom

min.: 127mm (5")

Pretest Speed & Temperature Functions

Connect the multisensor to the instrument and spin the 
paddlewheel. Check for a speed reading and the approximate air 
temperature. If there is no reading(s) or it is inaccurate, return the 
product to your place of purchase.

Mounting Location

CAUTION

: Do not mount in an area of turbulence or bubbles.

Near water intake or discharge openings
Behind strakes, struts, fittings, or hull irregularities

CAUTION

: Avoid mounting the sensor where the boat may be 

supported during trailering, launching, hauling, or storage.

• For the best performance, the sensor must be in contact with 

smooth water. To identify an area of clean water, observe the 
water flow off the transom while the boat is underway.

• Allow headroom space above the bracket for it to release and 

rotate the sensor upward (see Figure 1).

• Mount the sensor as close to the centerline (keel) of the boat as 

possible to ensure the transducer’s face remains in the water 
when the boat is turning.

Single drive boat

—Mount at least 75mm (3") beyond the 

swing radius of the propeller (see Figure 2). The starboard side 
where the propeller blades are moving downward is preferred.

Twin drive boat

—Mount the sensor between the drives.

Transducer

TRIDUCER

®

multisensor

Figure 2. Mounting location on single drive boat

max. with speed sensor:
213mm (8-1/2")

headroom

INSTALLATION INSTRUCTIONS

OWNER’S GUIDE      &

Record the information found on the cable tag for future reference.

Part No._________________Date___________Frequency________kHz

WARNING

Always wear safety goggles and a dust 

mask

 when installing to avoid personal injury.

CAUTION

Never use solvents

. Cleaners, fuel, 

sealants, paint, and other products may contain strong 

solvents, such as acetone, which attack many 

plastics, greatly reducing their strength.

IMPORTANT

:

 

Read the instructions completely

 

before proceeding with the installation. These 

instructions supersede any other instructions in your 

instrument manual if they differ.

Copyright © 2003 Airmar Technology Corp.

Copyright © 2003 Airmar Technology Corp.

NOTE: Starboard 
side of hull where 
propeller blades are 
moving downward is 
preferred.

Отзывы: