Trouble Shooting Guide
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation
or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any
faults, please check this Trouble Shooting Chart. If a problem cannot be remedied or you are experiencing
difficulty in installation, please call our Customer Service Department.
TROUBLE
1.If fan does not start:
2.If fan sounds noisy:
3.If fan wobbles:
4.If light does not work:
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch
housing.
CAUTION
: Make sure main power is turned off.
3.Make sure forward/reverse switch is firmly in up or down position. Fan will not
operate when switch is in the middle.
4.Make sure that the wall controler is " Turned On ".
1.Make sure all screws in motor housing are snug. (not over tightened)
2.Make sure the screws which attach the fan bladeholder to the motor are tight.
3.Make sure wire nut connectors in switch housing are not rattling against each
other or against the interior wall of the switch housing.
CAUTION
: Make sure main power is turned off before entering switch housing.
4.If using an optional ceiling fan light kit, check to be sure the screws securing
the glassware are finger tight. Check to be sure light bulb is tight in socket and
not touching glass shade(s). If vibration persists from glass, remove glass and
install a 1/4" wide rubber band on glass neck to act as an insulator. Replace
glass and tighten screws against rubber band.
5.Some fan motors are sensitive to signals from Solid State variable speed
controls. DO NOT USE a Solid State variable speed control.
6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will
disappear after this period.
All blades are weighed and grouped by weight. Natural woods vary in density
which could cause the fan to wobble even though all blades are weight-matched.
The following procedures should eliminate most of the wobble. Check for wobble
after each step.
1.Check that all blades are screwed firmly into blade holders.
2.Check that all blade holders are tightened securely to motor.
3.Make sure that canopy and mounting bracket are tightened securely to ceiling
junction box and junction box is mounted firmly to ceiling joist.
4.Most fan wobble problems are caused when blade levels are unequal. Check
this level by selecting a point on the ceiling above the tip of one of the blades.
Keeping measure within 1/8" rotate the fan until the next blade is positioned
for measurement. repeat for each blade. If all blade levels are not equal, you
can adjust blade levels by the following procedure. To adjust a blade tip down,
insert a washer (not supplied) between the blade and blade holder at the screw
closest to the motor. To adjust a blade tip up, insert washer (not supplied)
between the blade and blade holder at the two screws farthest from the motor.
5.If blade wobble is still noticeable, interchanging two adjacent (side by side)
blades can redistribute the weight and possibly result in smoother operation.
1.Check blue wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
CAUTION: Make sure main power is turned off before entering switch housing.
SUGGESTED REMEDY
WARNING:
To reduce the risk of personal injury, Do not bend the blade brackets when installing the brackets balancing the
blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
WARNING:
To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked acceptable for fan
support and use mounting screws provided with the outlet box.
WARNING:
To reduce the risk of fire, or electric shock, do not use this fan with any solid-state speed control device.
CAUTION:
To reduce the risk of personal injury, use only the two steel screws ( and lock washers ) provided with the fan
for mounting to the outlet box.
CAUTION:
To reduce the risk of personal injury, install the primary mounting means and use only the hardware provided
with the fan.
PAGE: 3 / 3
061128
TM
