manualshive.com logo in svg

Air innovations 99H0360-10, Инструкция по установке, эксплуатации и обслуживанию, Страница: 79 / 85

Поделиться
Скачать
Air innovations 99H0360-10 Скачать руководство пользователя страница 79

79 
 

Troubleshooting  

 

Before proceeding, read and understand the safety information contained in the Safety Section 

of the Wine Guardian Manual 

 

For in-depth Troubleshooting please head to:  

Help.wineguardian.com 

Typical start up problems 

 

Possible Cause 

Solution 

Loose, improper or defective remote 
interface controller or humidistat cable 

Check power, and remote interface  
controller or humidistat cable 

Incorrect remote interface controller 
or humidistat (optional) settings 

Check the remote interface controller and 
optional humidistat setup for the application 

Changed settings on the remote interface 
controller 

A common problem is not waiting long 
enough for the internal timers to complete 
their timed delay 

 

Unit does not start up 

Power Switch Light is Off 

Possible Cause 

Solution 

Switch not on 
No power to outlet 
Unit not plugged in 

Turn on switch 
Check circuit breaker and wiring 
Plug in the unit 

Power switch light is on and the remote interface controller light is off 

Possible Cause 

Solution 

No power to remote interface controller 

Check main control board for L.E.D.  

indication 
Check wiring for loose, broken or frayed 

connections 

Check wiring for proper splicing 
Remote interface controller may be faulty 

 

 

 

 

 

Power switch light is on and the remote interface controller light is on 

Possible Cause 

Solution 

Remote interface controller is not set 
up properly 

Check remote interface controller set up in the 
guide 

Press fan ON switch to check evaporator 
fan only 

 

Содержание 99H0360-10






















































































Отзывы:

Нет отзывов