manualshive.com logo in svg

Air innovations 99H0360-10, Инструкция по установке, эксплуатации и обслуживанию, Страница: 62 / 85

Поделиться
Скачать
Air innovations 99H0360-10 Скачать руководство пользователя страница 62

62 
 

Standard Controller Functions 
 

How to: 

 

 

Turn system 
on/off 

 
 
 
 

 

•

 

Press the “On/Off” button once. 

Note: There is a five (5) minute time delay 
before the system turns on or turns off. 

Change 
temperature 

 

•

 

Press the “Up” arrow once. The display will 
show the existing temperature setpoint. 

•

 

Press the up or down arrow buttons to adjust 
the temperature to the desired set point.  

Change humidity 

 

 

•

 

Press the “Up” arrow once. This display will 
show the existing temperature setpoint. 

•

 

Press the “Settings” button once to display the 

“Humidity” setpoint. 

•

 

Press the “Up” or “Down” arrows to adjust the 
humidity to the desired set point.  

Note: A Wine Guardian humidifier must be 

installed and Setting 6 set to “1” or “2” before 
the controller will let you change percent 
humidity.

 

Change Settings 
Cooling/ Heating 
/ Auto 

 

•

 

Press the Setting button once to display the 
setting function at the bottom of the screen. 

•

 

Press the Settings button again to scroll 
through settings for cool only, heat only or 
heat/cool only – auto mode. 

“Cool” Symbol 

Battery Life 

Humidity 

Settings and 
Defrost Area 

Temperature 

“Heat” Symbol 

Alarms 

Down Button      Settings Button 
         

On/Off Button   

Up Button 

         

Содержание 99H0360-10






















































































Отзывы:

Нет отзывов