Air innovations 99H0360-10 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 85

Air innovations 99H0360-10 Скачать руководство пользователя страница 35

35

Ceiling Mounting

Construct a structurally sound, level platform to place the unit on when hanging it from the ceiling
joists. The Wine Guardian is NOT designed to be suspended from the top of the unit; it must be
supported from the bottom. Place the unit on a platform to ensure that the unit is supported on all
four corners. Leave adequate space on the top of the unit to remove the access doors for service.

In all cases the unit must be level to /- 0.25 inches (+/- 6.35mm) end-to-end and +/- 1/8
inches (+/- 3.18mm) side-to-side for proper operation. Locate the unit as close to the wine cellar as
possible to reduce the length of the duct runs. If possible, use short and straight ducting on all
ductwork runs.

Typical Mounting Arrangements

The following illustrations are suggested mounting arrangements. These illustrations are not
intended to be complete and detailed installation drawings. For questions or help regarding
installation, contact a Wine Guardian distributor or email

([email protected])

a sketch of the

proposed area where the unit is to be installed

.

Handling and Installation

1)

Mount unit on solid, level surface.

2)

Allow sufficient space for access to unit and accessories.

3)

Provide proper electrical service.

4)

Provide water to humidifier.

5)

Install drain line with proper pitch

.

«
...
33
34
35
36
37
...
»

Содержание 99H0360-10






















































































Отзывы:

Нет отзывов