ANEST IWATA Europe S.r.l.
Corso Vigevano 46, 10155 Torino - Italy
Tel. 011-24 80 868 (4 linee ric. aut.)
Fax 011-85 19 44
IMPORTANT
This spray gun should be operated only by an adequately trained operator, for safe use and maintenance of the equipment.
Any misuse or handling other than those indicated in this Instruction Manual is not covered by guarantee. AIR GUNSA disclaims
all responsibility for any accident or damage caused by failure to observe the operational and safety procedures as from this
manual. In the interest of user friendliness, this manual contains information in a brief and concise form.
For any additional information you may require regarding. spray guns operations, or if any missing parts or any damage during
transportation is found, please contact your nearest ANEST IWATA Company (see last cover page).
AZ3 HTE SPRAY GUN
Before use, adjustment or maintenance, it is important to read this instruc-
tion manual very carefully. This manual must be stored in a safe place for
any future reference that may be necessary.
GB
MAIN SPECIFICATIONS
PROBLEMS AND REMEDIES
Problem
Where it
Parts to be
Cause
Remedy
occurred
checked
Retighten Adjust
Clean Replace
Air leaks
Air valve set
Air valve
*Dirt or damage on seat
x
x
(from tip
of air cap)
Air valve seat set
*Dirt or damage on seat
x
x
*Wear on air valve spring
x
O ring
*Damaged or deteriorated
x
Paint
Fluid nozzle
Fluid nozzle -
*Dirt, damage, wear
leaks
fluid needle set
on seat
x
x
*Loose fluid needle
adj. knob
x
*Wear on needle spring
x
Fluid nozzle -
*Insufficient tightening
x
gun body
*Dirt or damage on seat
x
x
Fluid needle -
*Needle does not return due
packing set
to packing set too tight
x
x
*Needle does not return due
to paint buildup
on fluid needle
x
x
Fluid needle
Needle packing
*Wear
x
x
set
Packing seat
*Insufficient tightening
x
Paint does not
Tip of gun
Fluid adj. knob
*Insufficient opening
x
flow
Tip hole of nozzle
*Clogged
x
Paint filter
*Clogged
x
x
E
UROPEAN
S
ALES
B
RANCHES
:
TROUBLESHOOTING
Spray Pattern
Problems
Remedies
1. Air enters between fluid nozzle and
1. Remove fluid nozzle to clean seat.
Fluttering
tapered seat of gun body.
If it is damaged, replace nozzle
2. Air is suctioned from fluid needle packing.
2. Thigten fluid needle packing.
1. Paint buildup on air cap, partially
1. Remove obstructions from horn holes.
Crescent
clogs horn holes. Air pressure from
But do not use metal objects to clean
both horns differs.
horn holes.
1. Paint buildup on the periphery of the fluid
1. Remove obstructions.
Inclined
nozzle hole or air cap center hole or damage.
Replace if damaged.
2. Loose fluid nozzle.
2. Remove fluid nozzle, clean seated section
1. Paint viscosity too low.
1. Add paint to increase viscosity.
Split
2. Fluid output too high.
2. Adjust fluid adj. knob or
pattern adj. knob.
Heavy
1. Paint viscosity too high.
1. Reduce viscosity.
Center
2. Fluid output too low.
2. Increase fluid output.
1. Fluid nozzle and fluid needle set are
1. Clean or replace fluid nozzle and fluid
Spit
not seating properly.
needle set.
2. The first-stage travel of trigger
2. Replace fluid nozzle and fluid
(when only air discharges) decreases.
needle set.
3. Paint buildup inside air cap set
3. Clean air cap set.
Instruction Manual
ANEST IWATA France S.A.
38074 Saint Quentin Fallavier
Cedex Centre Evolic B.P. 7405
Tél. 04 74 94 59 69
Fax 04 74 94 34 39
ANEST IWATA (U.K.) LTD
Unit 2, Cedar Trade Park,
Ferndown Industrial Estate,
Wimborne, Dorset - BH21 7SB U.K.
Tel. 01202 - 895999 Fax: 01202 -895666
AIR GUNSA S.r.l.
46, Corso Vigevano -10155 Torino - Italy
Tel. +39 011-24 80 868
Fax +39 011-85 19 44
www.anest-iwataeu.com
e-mail: [email protected]
Quality Air Spray Guns Since 1944
www.anest-iwataeu.com/airgunsa
Max. Working Pressure:
6.8 bar (98 PSI)
Noise Level (LAeqT)
77,6 dB (A)
Temperature range:
5~40C°
MA0004EREV
.1
Manufactured by:
AIR GUNSA S.r.l. - Via degli Arceri, 1 - 20010 Cardano al Campo (VA) Italy
18
18-1
B
E
Air Nipple 1/4”BSP
Paint cup screw 1/4” BSP
Model
Type
Orifice nozzle
Air cap
Fluid output Pattern widht
Air consumption
Weight
of feed
ø mm
code
Ml/min
mm
Nl/min
With cup Without cup
1,0
W2010135110
80
170
200
1,3
W2010135113
150
240
200
1,5
W2010135115
190
260
200
1,8
W2010135118
260
300
205
2,0
W2010135120
265
310
205
2,5
W2010131400
424
340
279
2,8
W2010133300
427
350
291
3,0
W2010131500
489
360
288
3,5
W2010131600
490
340
307
680
AZ3 HTE
Gravity
2.0 bar
3.0 bar
540
570
710
NOTE: for spare parts list see on page 3.
