This
AIR GUNSA
spray guns kit complies to ATEX regulations 94/9/EC, protection level:
II 2 G X Suitable for using Zones 1 and 2.
X marking: Any static electricity discharge from the spray gun is to be diverted to the ground via the conductive air hose as stipulated.
IMPORTANT
This spray gun should be operated only by an adequately trained operator, for safe use and maintenance of the equipment. Any
misuse or handling other than those indicated in this Instruction Manual is not covered by guarantee. AIR GUNSA disclaims all
responsibility for any accident or damage caused by failure to observe the operational and safety procedures as from this man-
ual. In the interest of user friendliness, this manual contains information in a brief and concise form.
For any additional information you may require regarding spray guns operations, or if any missing parts or any damage during
transportation is found, please contact your nearest AIR GUNSA Company (see last cover page).
IMPORTANT SPECIFICATIONS
Be sure to observe warnings and cautions in this instruction manual.
If not, it can cause paint ejection and serious bodily injury by drawing organic solvent.
Be sure to observe following marked items which are especially important.
WARNING
Indicates a potentially hazardous situation which, if not avoided, may result in serious injury or loss of life.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or pro-
perty damage.
IMPORTANT
Indicates notes which we ask you to observe. The safety precautions in this instruction manual are the mini-
mum necessary conditions. Follow national and local regulations regarding fire prevention, electricity and
safety as well as your own company regulations.
TECHNICAL SPECIFICATIONS
Manufactured by:
AIR GUNSA _ Anest Iwata Gruop
(1)
Atomizing air pressure means air pressure at gun inlet when trigger is pulled and air flows.
(2)
Paint viscosity:
21 sec/Ford cup#4 AZ10 HTE SP
54 sec/Ford cup#4 AZ10 HTE PC
Before use, adjustment or maintenance, it is important to read this instruction manual very
carefully. This manual must be stored in a safe place for any future reference that may be necessary.
GB
Model
Nozzle Air
Cap
(1)
Atomizing
(2)
Fluid
Air
Pattern
Orifice
set Mark
Air pressure
Output
Consumption
Width
Ø mm (in)
bar (PSI)
ml/min
Nl/min (cfm)
mm (in)
AZ10 HTE SP / AZ10 HTE SP AV / AZ10 HTE PC Pressure feed
AZ10 HTE SP 0.8
0.8 (0.031)
08
150
210 (7.41)
190 (7.48)
AZ10 HTE SP 1.0
1.0 (0.039)
10
150
210 (7.41)
200 (7.87)
AZ10 HTE SP 1.3
1.3 (0.051)
13
200
210 (7.41)
230 (9.05)
AZ10 HTE SP 1.5
1.5 (0.059)
15
200
210 (7.41)
240 (9.45)
AZ10 HTE SP 1.8
1.8 (0.070)
18
250
280 (9.89)
280 (11.02)
AZ10 HTE SP 2.0
2.0 (0.079)
20
250
280 (9.89)
290 (11.42)
AZ10 HTE SP 2.5
2.5 (0.098)
25
300
290 (10.23)
300 (11.81)
AZ10 HTE PC with Pressure Container
AZ10 HTE PC 1.5
1.5 (0.059)
15
180 (6.36)
AZ10 HTE PC 1.8
1.8 (0.070)
18
250 (8.83)
AZ10 HTE PC 2.0
2.0 (0.079)
20
250 (8.83)
AZ10 HTE PC 2.5
2.5 (0.098)
25
190 (6.71)
2.5 (36)
2.5 (36)
300-400
(11.81-
15.75)
_
ANEST IWATA Europe S.r.l.
46, Corso Vigevano
10155 Torino - Italy
Tel. ++39 011 24 80 868
Fax ++39 011 22 74 406
www.anest-iwataeu.com
e-mail: [email protected]
Instruction Manual
AIR GUNSA s.r.l.
46, Corso Vigevano
10155 Torino - Italy
Tel. ++39 011 24 80 868
Fax ++39 011 22 74 406
Quality Air Spray Guns Since 1944
www.anest-iwataeu.com/airgunsa
Distributed by:
Recommended condition
Max. Pressure:
7.0 bar (100 PSI)
Max. Temperature:
Noise Level (LAeqT)
75.2 dB (A) AZ10 HTE SP
Atmosphere
5 ~ 40 °C
73.7 dB (A) AZ10 HTE PC
Air and fluid
5 ~ 43 °C
Spray conditions
Recommended condition in Tech. Specifications
Air connection
G 1/4”
Measuring point
1m backwards from gun, 1,6 m height
Model
Weight Fluid
g (lbs)
Connection
AZ10 HTE SP 1/4”
480 (1.06)
G 1/4” M
AZ10 HTE SP 3/8”
480 (1.06)
G 3/8” M
AZ10 HTE SP AV 1/4”
490 (1.08)
G 1/4” M
AZ10 HTE SP AV 3/8”
490 (1.08)
G 3/8” M
AZ10 HTE PC
970 (2.13)
M16x1 F
SPRAY GUN AZ10 HTE SP 1/4”- AZ10 HTE SP 3/8”
AZ10 HTE SP AV 1/4”- AZ10 HTE SP AV 3/8”- AZ10 HTE PC
