Aim PDM 32 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 63

background image

www.aim-sportline.com

- PDM 32 User Guide

47

18.

SmartyCam stream setting

The PDM 32 can be connected to AiM SmartyCam to show the data you wish on SmartyCam video. To set
each channel:

•

click on it and a setting panel shows up

•

it shows all channels and/or sensors that fits the selected function

•

in case you do not find the channel or the sensor in the list enable “Enable all channels for functions”

checkbox and all channels/sensors will be shown

«
...
46
47
48
49
50
...
»

Содержание PDM 32
































































Отзывы:

Нет отзывов

Похожие инструкции для PDM 32

Бренд: V7 Страницы: 20

Бренд: CAYMON Страницы: 4

Optima 520 Series

Бренд: Marway Страницы: 14

Бренд: Vertiv Страницы: 16

PLUGMOLD PM48TC

Бренд: LEGRAND Страницы: 2

Бренд: EuroLite Страницы: 15

Бренд: EuroLite Страницы: 15

Бренд: EuroLite Страницы: 16

Бренд: Panamax Страницы: 2

PX3-4000 series

Бренд: Raritan Страницы: 688

xComfort CBEU-02/01

Бренд: Eaton Страницы: 4

PerfectWave PowerBase

Бренд: PS Audio Страницы: 12

Бренд: Showgear Страницы: 16

Бренд: Showgear Страницы: 16

SURGE GUARD 44280

Бренд: Southwire Страницы: 2

Бренд: Skyrc Страницы: 39

Бренд: Furman Страницы: 8

P-3600 AR G prestige series

Бренд: Furman Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды