Aim-TTI TGR2050 Series Скачать руководство пользователя страница 7

Страница: 7 / 100

2 - Installation

Mounting

TGR2050 Series Instruction Manual

INSTALLATION

Mounting

This instrument is suitable for bench use and rack mounting.
For rack mounting the protective bezels and handle/stand should be removed such

that the instrument can be fitted beside any other standard 2U half-rack instrument

in a 19” rack. A suitable 2U 19” rack kit is available from the manufacturers or their

overseas agents.
See rack mount instructions for details on how to remove the protective bezel and

handle.

Ventilation

The instrument uses a fan fitted to the rear panel. Take care not to restrict the rear

air exit or the inlet vents at the front (sides and underneath). In rack-mounted

situations allow adequate space around the instrument and/or use a fan tray for

forced cooling.

Handle/stand

The instrument is fitted with a 4-position handle/stand. Pull out both sides of the

handle at the case pivot points to free the position locking pegs and rotate the

handle from the stowed position to the required stand or handle position. Release

the sides of the handle to lock it in the new position.

Содержание TGR2050 Series





































































































Результаты поиска

Содержание TGR2050 Series

Отзывы:

Бренды по названию

Популярные бренды

Aim-TTI TGR2050 Series, Инструкция по эксплуатации

Результаты поиска

Содержание TGR2050 Series

Отзывы:

Бренды по названию

Популярные бренды