manualshive.com logo in svg

Aim-TTI LD400, Инструкция по эксплуатации

Поделиться
Скачать
Aim-TTI LD400 Скачать руководство пользователя страница 36

  

   

 

35 

USB Interface and Device Driver Installation 

The instrument firmware can be updated in the field through the USB port. This does

 not

 need 

the driver described here. It requires a PC software utility provided by the manufacturer, and uses 
a HID driver that will already be installed on the PC. If that is the only USB functionality required, 
download the package containing the firmware update together with the PC utility from the 
manufacturer, and follow the instructions included. 

Using the USB interface for remote control requires a Communications Device Class driver on 
the PC to provide a virtual COM port instance. In Windows a suitable driver is provided by 
Microsoft, but it is not installed by default. The data (.INF) file to control the installation is provided 
on the Product Documentation CD delivered with the unit; however the same driver is also used 
by many other instruments from this manufacturer and may already be known to the PC. 

To install the driver for the first time, first switch the unit on, and then connect the USB port to the 
PC. The Windows plug and play functions should automatically recognise the attachment of new 
hardware to the USB interface and (possibly after searching the internet for some time) prompt 
for the location of a suitable driver. Follow the Windows prompts and point to the CD, then the 
sub-directory for this product, and then to the USB Driver sub-directory below that. The file is 
named USB_ARM_VCP_xxx

.

INF, where xxx is a version number. (A readme.pdf file will also be 

found in that directory if further assistance is needed.)  

In some cases Windows will not complete this procedure (especially recent versions which 
search the internet first, looking for the unique Vendor ID and Product ID), in which case the 
instrument will show in Device Manager as “not working properly”. If this happens, select this 
device, right click and choose “update driver software...” and then “browse this computer for 
driver software...” and then locate the .INF file on the CD as described above. 

Once Windows has installed the device driver it will assign a COM port number to this particular 
unit. This number will depend on previous COM port assignments on this PC, and it may be 
necessary to use Device Manager to discover it. Each instrument has a unique USB identifier 
which is remembered by the system, so it will receive the same COM port number whenever it is 
attached to the same PC (regardless of the physical interface socket used), even though the 
COM port will disappear while the instrument is disconnected or switched off. Other instruments 
will receive different COM port numbers.  

Note that a different PC will not necessarily assign the same COM port number to a particular 
instrument (it depends on the history of installations), however Device Manager can be used to 
change the assignments given. 

This virtual COM port can be driven by Windows applications (including a terminal emulator) in 
exactly the same way as any standard COM port, except that the Baud rate and other settings 
are unnecessary and are ignored. Some old applications might not function with COM port 
numbers 3 or 4, or above 9. In this case, use Device Manager to change the allocation given. 
Once it is installed, the driver will be maintained by Windows Update in the usual way. 

LAN Interface 

 

The LAN interface is designed to comply with the LXI standard version 1.4 LXI Core 2011 and 
contains the interfaces and protocols described below. For more information on LXI standards 
refer to  

www.lxistandard.org

 . 

When powered up and attached to a network, the unit will by default attempt to obtain IP address 
and netmask settings via DHCP, or, if DHCP times out (after 30 seconds), via Auto-IP.  In the 
very unlikely event that an Auto-IP address cannot be found a static IP address is assigned; the 
default is 192.168.0.100, but this can be changed on the web page. Connecting via a router is 
recommended as this is significantly quicker to assign an IP address; connecting directly to a PC 
will only begin to assign an Auto-IP address after the 30 second DHCP timeout.   

Since it is possible to misconfigure the LAN interface, making it impossible to communicate with 
the instrument over LAN, a LAN Configuration Initialise (LCI) mechanism is provided via a push 
switch (marked 

LAN reset)

 accessible through a small hole in the rear panel. This restores the 

Содержание LD400























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды