manualshive.com logo in svg

AIC Nesta N 120 FS, Руководство по установке и обслуживанию, Страница: 27 / 72

Поделиться
Скачать
AIC Nesta N 120 FS Скачать руководство пользователя страница 27

Fig. 9.  Removing/Installing the Access Panels

 2

 1

I-27

A-070336_EN • Rev. A

P

roduct

 I

nstallatIon

Removing and Installing the Access Panels

Conditions:

Tools and Material: 

 

î

Wrench, hex head, size 4

Removal Procedure:

Bottom Front Panel

1. 

Pull on the panel to disengage the center 

stud from its receptacle.

Center Front Panel

1. 

Release the top screw (

2

) from the right side 

bottom panel.

2. 

Pull on the panel to disengage the studs from 

their receptacles.

Top panel 

1. 

Release the top screw (

1

) from the right side 

top panel.

2. 

Push the top panel upwards to disengage 

the studs from their receptacles.

Side Panels

1. 

Top: remove four screws. Retain hardware 

for reinstallation.

2. 

Bottom: remove six screws. Retain hardware 

for reinstallation.

Installation procedure

Bottom Front Panel

1. 

Push the panel in position to engage the 

center stud into its receptacle.

Center Front Panel

1. 

Push the panel in position to engage the 

studs into their receptacles.

OFF

Top panel 

1. 

Push the top panel downwards to engage 

the studs into their receptacles.

Side Panels

1. 

Bottom: install six retained screws.

2. 

Top : Install four retained screws.

Follow-on task(s):

If only the top and center front panels were re-

moved, but not the side panels, tighten one top 

screw (

2

) on the right side bottom panel, and one 

top screw on the right side top panel (

1

).

Содержание Nesta N 120 FS









































































Отзывы:

Нет отзывов