background image

19

ELECTRIC ATTACHMENT CLUTCHES

FIGURE  42

FIGURE  43 

VIEW OF BOTTOM 

STEP 43:  (SEE FIGURE 43)

•  Attach the two rear pulley frame brackets to the inside 

of the clutch/idler assembly using two 5/16" x 1" hex 
bolts, eight 5/16" washers and two 5/16" nylock nuts 
for each bracket. 

•  Attach the two front pulley frame brackets to the inside 

of the clutch/idler assembly using two 5/16" x 3/4" hex 
bolts, 5/16" washers and 5/16" nylock nuts for each 
bracket.

STEP 44: (SEE TABLE 2)

 

Two different length drive belts are included with 
your snow thrower. Use the table below to select 
the correct drive belt for your type tractor. The part 
number is printed on the outside of the belt .

• 

Set aside the belt that is not for your tractor to avoid 
accidentally using it.

55" BELT (PART #46989)

 

TRACTOR TYPE 

DECK SIZE 

CLUTCH TYPE

56" BELT (PART #48138)

 

TRACTOR TYPE 

DECK SIZE 

CLUTCH TYPE

  (LT) Lawn Tractor 

48" 

Electric

  (LT) Lawn Tractor 

38", 42", 46" 

Electric

TABLE 2

STEP 41:  (SEE FIGURE 41)

•  Turn the clutch idler assembly upside down.
•  Hook the spring (onto the end of the bolt that extends 

through the nut on the bottom of the upper idler arm. 
Install a 3/8" hex lock nut onto the bolt, leaving enough 
space for the spring to pivot.

FIGURE  41

STEP 42:  (SEE FIGURE 42)

•  Insert tensioning chains through the holes shown and 

attach to the springs on the upper and lower idler arms.

•  Attach a 3/32" hairpin cotter to the chain attached to 

the upper idler arm, placing it in the fifth link from the 
spring.

3/8" HEX
LOCK NUT

SPRING

ATTACH
SPRING
HERE

TENSIONING CHAIN (lower idler arm)

TENSIONING CHAIN (upper idler arm)

3/32" HAIRPIN
COTTER IN
5th LINK

5/16" x 3/4" HEX BOLT

5/16" x 1"
HEX BOLT

5/16" NYLOCK NUT

5/16"
WASHER

(4) 5/16" WASHERS

Содержание LST42E





































Отзывы: