manualshive.com logo in svg

Agilent Technologies U9391C, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Agilent Technologies U9391C Скачать руководство пользователя страница 8

8

Agilent U9391C/F Comb Generator Operating and Service Manual 

1

Introduction

Product Overview

The U9391C/F comb generator was designed as a phase 
reference standard for the Agilent PNA- X nonlinear vector 
network analyzer (NVNA). It was developed to provide 
precision phase calibration, traceable to the National Institute 
of Standards and Technology (NIST).

NVNA component characterization software converts a 4- port 
PNA- X with option 510 into an innovative, high- performance, 
non- linear network analyzer which uses U9391C/F comb 
generators as precision phase calibration standards. Comb 
generators generate frequency harmonics at integer multiples of 
an RF input signal.

Generally, comb generators available in the open market today 
are made with SRD diodes, U9391C/F comb generators are 
based on Agilent InP MMIC technology to ensure superior phase 
stability of the combs.

Figure 1-1

U9391C Comb Generator

Содержание U9391C








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды