background image

Safety and Support Information

5

Table 1

Safety Symbols and Markings

Safety symbols

Warning: risk of electric shock.

Caution: refer to accompanying documents.

Alternating current.

Both direct and alternating current.

Earth (ground) terminal

Protective earth (ground) terminal

Frame or chassis terminal

Terminal is at earth potential. Used for measurement and control 
circuits designed to be operated with one terminal at earth potential.

Switch setting indicator. 

= Off, | = On.

Standby (supply); units with this symbol are not completely 
disconnected from ac mains when this switch is off. To completely 
disconnect the unit from ac mains, either disconnect the power cord, or 
have a qualified electrician install an external switch.

Regulatory Markings

The CE mark is a registered trademark of the European Community.

The CSA mark is a registered trademark of the Canadian Standards 
Association.

The C-tick mark is a registered trademark of the Spectrum Management 
Agency of Australia. This signifies compliance with the Australian EMC 
Framework regulations under the terms of the Radio Communications 
Act of 1992.

ISM 1-A

This text indicates that the product is an Industrial Scientific and 
Medical Group 1 Class A product (CISPR 11, Clause 4).

N10149

Содержание TS-5410































Отзывы: