Agilent Technologies PL-GPC 220 Скачать руководство пользователя страница 34

Страница: 34 / 120

PL-GPC 220 User Manual

Using the Module

The Graphical User Interface

Autosampler

• Autosampler (offline/online)

– This button is used to start and stop the

autosampler.

• Offline

– indicates that the autosampler is not in use.

• Online

– indicates that the autosampler is in use and running using the

parameters set up in autosampler configuration screen.

• Inject

– this button is used to manually change the injection valve position,

see

“Injection Sequence”

on page 17 for the description of positions. This

tab also shows the position of the injection valve during the running
sequence.

Configuring the Controlled Modules - Configuration Editors

To change any of the set conditions, simply click on the coloured section of the
instrument graphic to open the configuration editor for that module.

Содержание PL-GPC 220

























































































































Результаты поиска

Содержание PL-GPC 220

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies PL-GPC 220, Руководство пользователя

Результаты поиска

Содержание PL-GPC 220

Отзывы:

Бренды по названию

Популярные бренды