manualshive.com logo in svg

Agilent Technologies PL-GPC 220, Руководство пользователя

Поделиться
Скачать
Agilent Technologies PL-GPC 220 Скачать руководство пользователя страница 113

PL-GPC 220 User Manual

113

Appendix

9

The Waste Electrical and Electronic Equipment Directive

The Waste Electrical and Electronic Equipment Directive 

Abstract

The Waste Electrical and Electronic Equipment (WEEE) Directive 
(2002/96/EC), adopted by EU Commission on 13 February 2003, is 
introducing producer responsibility on all electric and electronic appliances 
starting with 13 August 2005.

N O T E

This product complies with the WEEE Directive (2002/96/EC) marking requirements. The 
affixed label indicates that you must not discard this electrical/electronic product in 
domestic household waste.

Product Category: 

With reference to the equipment types in the WEEE Directive Annex I, this product is 
classed as a Monitoring and Control Instrumentation product.

N O T E

Do not dispose off in domestic household waste

To return unwanted products, contact your local Agilent office, or see 

www.agilent.com

 for 

more information.

Содержание PL-GPC 220

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды