Agilent Technologies n5181a Скачать руководство пользователя страница 59

Страница: 59 / 202

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Troubleshooting

Pulse Modulation Problems (N5183A)

1-51

•

If the measured voltage is not > 2.5 Vp–p on ALC J1-E3, replace the A3 RF assembly.

•

If the measured voltage is > 2.5 Vp–p on ALC J1-E3, replace the A7 Micro Deck.

Go to

Chapter 4, "Post-Repair Procedures and Performance Verification"

Pulse Modulation Problems (N5183A)

Remove the external cover and the top inside cover. Refer to

Chapter 3, "Assembly Replacement"

for instructions on removing the

instrument covers.

Set up the signal generator:

Press

Preset

Press

FREQ

GHz

Press

RF On/Off

to On.

Press

AMPTD

dBm

Press

Pulse

Pulse Off On

to On.

Press

Pulse Period

usec

Press

Pulse Width

usec

Using a spectrum analyzer, verify that pulse modulation is present on the RF output.

Press

FREQ

GHz

Using a spectrum analyzer, verify that pulse modulation is present on the RF output.

If no pulse modulation is present at either frequency, replace the A3 RF Assembly and go to

step 11

If pulse modulation is present at 5 GHz, but is not present at 2 GHz, replace the A3 RF Assembly and go to

step 11

Figure 1-21 ALC J1-A7

J1-A7

深圳德标仪器

135-1095-0799

Содержание n5181a











































































































































































































Результаты поиска

Содержание n5181a

Отзывы:

Agilent Technologies n5181a, Руководство по обслуживанию, Страница: 59 / 202

Результаты поиска

Содержание n5181a

Отзывы: