manualshive.com logo in svg

Agilent Technologies Infinium DCA 86100A, Руководство по обслуживанию

Поделиться
Скачать
Agilent Technologies Infinium DCA 86100A Скачать руководство пользователя страница 9

1-3

General Information

Safety Information

Safety Information

Before servicing the mainframe, familiarize yourself with the safety markings on the instrument 
and the safety instructions in this manual. This instrument has been manufactured and tested 
according to international safety standards. To ensure safe operation of the instrument and the 
personal safety of the user and service personnel, the cautions and warnings in this manual must 
be heeded. Refer to the summary of safety considerations at the front of this manual. 

This product has been designed and tested in accordance with IEC Publication 1010, Safety 
Requirements for Electronic Measuring Apparatus, and has been supplied in a safe condition. 
The instruction documentation contains information and warnings which must be followed by 
the user to ensure safe operation and to maintain the product in a safe condition.

WA R N I N G

These servicing instructions are for use by qualified personnel only. To avoid electrical shock, do 
not perform any servicing unless you are qualified to do so.

WA R N I N G

The opening of covers or removal of parts is likely to expose dangerous voltages. Disconnect the 
product from all voltage sources while it is opened.

WA R N I N G

The power cord is connected to internal capacitors that may remain live for five seconds after 
disconnecting the plug from its power supply.

WA R N I N G

The detachable power cord is the instrument disconnecting device. It disconnects the mains 
circuits from the mains supply before other parts of the instrument. The front panel switch is only 
a standby switch and is not a LINE switch (disconnecting device).

WA R N I N G

This is a Safety Class 1 Product (provided with a protective earthing ground incorporated in the 
power cord). The mains plug shall only be inserted in a socket outlet provided with a protective 
earth contact. Any interruption of the protective conductor inside or outside of the product is likely 
to make the product dangerous. Intentional interruption is prohibited.

WA R N I N G

Use of controls or adjustment or performance of procedures other than those specified herein may 
result in hazardous radiation exposure.

C A U T I O N

Clean the cabinet using a damp cloth only.

N O T E

The warranty is null and void on instruments that have had the seals broken by the customer. The 
instrument should only be disassembled by Agilent Technologies Customer Engineers.

Содержание Infinium DCA 86100A













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды