Agilent Technologies G7104A Скачать руководство пользователя страница 76

Страница: 76 / 234

Agilent 1290 Infinity II Flexible Pump User Manual

Error Information

Pump Error Messages

Drive Encoder failed

Error ID: 29210

Drive encoder failed during pump drive calibration.

Drive phases differ too much in electric resistance

Error ID: 29216

Pump drive calibration has failed due to a strong difference electric
resistances for different motor phases.

Probable cause

Suggested actions

Internal error.

Contact Agilent support.

Probable cause

Suggested actions

Pump drive cable defect.

Please contact your Agilent service
representative.

Pump drive defect.

Please contact your Agilent service
representative.

Defective main board.

Please contact your Agilent service
representative.

Содержание G7104A











































































































































































































































Результаты поиска

Содержание G7104A

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies G7104A, Руководство пользователя

Результаты поиска

Содержание G7104A

Отзывы:

Бренды по названию

Популярные бренды