manualshive.com logo in svg

Agilent Technologies G7104A, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G7104A Скачать руководство пользователя страница 74

74

Agilent 1290 Infinity II Flexible Pump User Manual

6

Error Information

Pump Error Messages

Timeout: Wait for run volume

Error ID: 29181

A target condition (run volume, which is the volume delivered since the 
method run start) has been sent to the instrument which should have 
been reached within an expected time frame but didn’t. Either the limit, 
time frame or the current value of the variable has been modified later 
directly or indirectly (for example the flow rate).

Timeout: Wait for Volume

Error ID: 29182

A target condition (volume, which is the delivered flow since the limit has 
been set) has been sent to the instrument which should have been reached 
within an expected time frame but didn’t. Either the limit, time frame or 
the current value of the variable has been modified later directly or 
indirectly (for example the flow rate).

Probable cause

Suggested actions

1

Incorrect parameters have been sent to the 
instrument by the control software or 
manual changes.

Verify control software, macros, manual 
commands.

Probable cause

Suggested actions

1

Incorrect parameters have been sent to the 
instrument by the control software or 
manual changes.

Verify control software, macros, manual 
commands.

Содержание G7104A











































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды