Agilent Technologies G7104A Скачать руководство пользователя страница 71

Страница: 71 / 234

Agilent 1290 Infinity II Flexible Pump User Manual

Error Information

Pump Error Messages

Writing the multi purpose valve tag failed

Error ID: 29241

Writing the multi purpose valve tag failed.

•

Parameter: None

Unknown multi purpose valve type

Error ID: 29242

The type information of the multi purpose valve is invalid.

•

Parameter: None

Pump drive encoder error

Error ID: 29211

The pump drive encoder has generated no signal.

•

Parameter: 1 – 2 referring to pump drive

Probable cause

Suggested actions

Multi purpose valve head tag defect.

Replace multi purpose valve head.

Multi purpose valve tag head reader is
defect.

Please contact your Agilent service
representative.

Probable cause

Suggested actions

Wrong valve head installed.

Check or replace multi purpose valve head.

Valve head has invalid RFID tag content.

Check or replace multi purpose valve head.

Probable cause

Suggested actions

Pump drive encoder is defect.

Please contact your Agilent service
representative.

Содержание G7104A











































































































































































































































Результаты поиска

Содержание G7104A

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies G7104A, Руководство пользователя

Результаты поиска

Содержание G7104A

Отзывы:

Бренды по названию

Популярные бренды