manualshive.com logo in svg

Agilent Technologies G7104A, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G7104A Скачать руководство пользователя страница 24

24

Agilent 1290 Infinity II Flexible Pump User Manual

2

Site Requirements and Specifications

Site Requirements

Site Requirements

A suitable environment is important to ensure optimal performance of the 
instrument.

Power Considerations

The module power supply has wide ranging capability. It accepts any line 
voltage in the range described in 

Table 1

 on page 27. Consequently there 

is no voltage selector in the rear of the module. There are also no 
externally accessible fuses, because automatic electronic fuses are 
implemented in the power supply.

WA R N I N G

Hazard of electrical shock or damage of your instrumentation

can result, if the devices are connected to a line voltage higher than specified.

➔

Connect your instrument to the specified line voltage only.

WA R N I N G

The module is partially energized when switched off, as long as the power cord is 
plugged in. 

Repair work at the module can lead to personal injuries, e.g. electrical shock, when 
the cover is opened and the module is connected to power.

➔

Always unplug the power cable before opening the cover.

➔

Do not connect the power cable to the instrument while the covers are removed.

C A U T I O N

Inaccessible power plug.

In case of emergency it must be possible to disconnect the instrument from the power 
line at any time.

➔

Make sure the power connector of the instrument can be easily reached and 
unplugged.

➔

Provide sufficient space behind the power socket of the instrument to unplug the 
cable.

Содержание G7104A











































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды