manualshive.com logo in svg

Agilent Technologies G7104A, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G7104A Скачать руководство пользователя страница 220

220

Agilent 1290 Infinity II Flexible Pump User Manual

12

Appendix

General Safety Information

General Safety Information

General Safety Information

The following general safety precautions must be observed during all 
phases of operation, service, and repair of this instrument. Failure to 
comply with these precautions or with specific warnings elsewhere in this 
manual violates safety standards of design, manufacture, and intended use 
of the instrument. Agilent Technologies assumes no liability for the 
customer’s failure to comply with these requirements.

Safety Standards

This is a Safety Class I instrument (provided with terminal for protective 
earthing) and has been manufactured and tested according to 
international safety standards. 

General

Do not use this product in any manner not specified by the manufacturer. 
The protective features of this product may be impaired if it is used in a 
manner not specified in the operation instructions.

WA R N I N G

Ensure the proper usage of the equipment.

The protection provided by the equipment may be impaired.

➔

The operator of this instrument is advised to use the equipment in a manner as 
specified in this manual.

Содержание G7104A











































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды