manualshive.com logo in svg

Agilent Technologies G7104A, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G7104A Скачать руководство пользователя страница 201

Agilent 1290 Infinity II Flexible Pump User Manual

201

LAN Configuration

11

Automatic configuration with Bootp

Automatic configuration with Bootp

About Agilent BootP Service

The Agilent BootP Service is used to assign the LAN Interface with an IP 
address. 

The Agilent BootP Service is provided on the ChemStation DVD. The 
Agilent BootP Service is installed on a server or PC on the LAN to 
provide central administration of IP addresses for Agilent instruments on 
a LAN. The BootP service must be running TCP/IP network protocol and 
cannot run a DHCP server.

N O T E

All examples shown in this chapter will not work in your environment. You need your own 
IP-, Subnet-Mask- and Gateway addresses.

N O T E

Assure that the detector configuration switch is set properly. The setting should be either 

BootP

 or 

BootP & Store

, see 

Table 11

 on page 193.

N O T E

Assure that the detector connected to the network is powered off.

N O T E

If the Agilent BootP Service program is not already installed on your PC, then install it from 
your Agilent ChemStation DVD, located in folder 

BootP

.

Содержание G7104A











































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды