manualshive.com logo in svg

Agilent Technologies G7104A, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G7104A Скачать руководство пользователя страница 177

Agilent 1290 Infinity II Flexible Pump User Manual

177

Hardware Information

10

Electrical Connections

Electrical Connections

•

The CAN bus is a serial bus with high speed data transfer. The two 
connectors for the CAN bus are used for internal module data transfer 
and synchronization.

•

The REMOTE connector may be used in combination with other 
analytical instruments from Agilent Technologies if you want to use 
features such as start, stop, common shut down, prepare, and so on.

•

With the appropriate software, the RS- 232C connector may be used to 
control the module from a computer through a RS- 232C connection. 
This connector is activated and can be configured with the 
configuration switch.

•

The power input socket accepts a line voltage of 100 – 240 VAC ± 10 % 
with a line frequency of 50 or 60 Hz. Maximum power consumption 
varies by module. There is no voltage selector on your module because 
the power supply has wide- ranging capability. There are no externally 
accessible fuses, because automatic electronic fuses are implemented in 
the power supply.

N O T E

Never use cables other than the ones supplied by Agilent Technologies to ensure proper 
functionality and compliance with safety or EMC regulations.

Содержание G7104A











































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды