Agilent Technologies G7104A Скачать руководство пользователя страница 140

Страница: 140 / 234

140

Agilent 1290 Infinity II Flexible Pump User Manual

Maintenance

Replace the Module Firmware

To upgrade/downgrade the module’s firmware carry out the following
steps:

Download the required module firmware, the latest LAN/USB FW
Update Tool and the documentation from the Agilent web.

http://www.chem.agilent.com/_layouts/agilent/downloadFirmware.aspx?whid=69761

For loading the firmware into the module follow the instructions in the
documentation.

Module Specific Information

There is no specific information for this module.

When

The installation of newer firmware might be necessary

•

if a newer version solves problems of older versions or

•

to keep all systems on the same (validated) revision.

The installation of older firmware might be necessary

•

to keep all systems on the same (validated) revision or

•

if a new module with newer firmware is added to a system or

•

if third party control software requires a special version.

Tools required

Description

Agilent Lab Advisor software

Instant Pilot G4208A
(only if supported by module)

Parts required

Description

Firmware, tools and documentation from Agilent web site

Preparations

Read update documentation provided with the Firmware Update Tool.

Содержание G7104A











































































































































































































































Результаты поиска

Содержание G7104A

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies G7104A, Руководство пользователя

Результаты поиска

Содержание G7104A

Отзывы:

Бренды по названию

Популярные бренды