manualshive.com logo in svg

Agilent Technologies G1314B, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G1314B Скачать руководство пользователя страница 96

96

Agilent 1260 Infinity VWD User Manual

7

Error Information

Detector Error Messages

No heater current

Error ID: 7453

The lamp heater current in the detector is missing. During lamp ignition, 
the processor monitors the heater current. If the current does not rise 
above the lower limit within 1 , the error message is generated.

Probable cause

Suggested actions

1

Lamp disconnected.

Ensure the lamp is connected.

2

Ignition started without the top foam in 
place.

Please contact your Agilent service 
representative.

3

Fan not running (permitting lamp on).

Please contact your Agilent service 
representative.

4

Defective main board.

Please contact your Agilent service 
representative.

5

Defective or non-Agilent lamp.

Exchange the lamp.

6

Defective power supply.

Please contact your Agilent service 
representative.

Содержание G1314B

















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды