Agilent Technologies G1314B Скачать руководство пользователя страница 53

Страница: 53 / 208

Agilent 1260 Infinity VWD User Manual

Using the Detector

Setting up an Analysis

Requirements and Conditions

What You Will Need

The table below lists the items you need to have for the set up of the
analysis. Some of these are optional (not required for the basic system).

Table 7

What you will need

Agilent 1200
Infinity Series
system

Pump (plus degassing)

Autosampler

Detector, standard flow cell installed

Degasser (optional)

Column Compartment (optional)

Agilent ChemStation or
Instant Pilot G4208, optional for basic operation.

System should be correctly set up for LAN communication with the Agilent
ChemStation

Column:

Zorbax Eclipse XDB-C18, 4.6 x 150 mm, 5 µm (993967-902) or an equivalent
column

Standard:

Agilent isocratic checkout sample (01080-68704)

Содержание G1314B

















































































































































































































Результаты поиска

Содержание G1314B

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies G1314B, Руководство пользователя

Результаты поиска

Содержание G1314B

Отзывы:

Бренды по названию

Популярные бренды