manualshive.com logo in svg

Agilent Technologies G1314B, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G1314B Скачать руководство пользователя страница 39

Agilent 1260 Infinity VWD User Manual

39

Installing the Detector

3

Installation Information on Leak and Waste Handling

Installation Information on Leak and Waste Handling

The Agilent 1200 Infinity Series has been designed for safe leak and waste 
handling. It is important that all security concepts are understood and 
instructions are carefully followed.

WA R N I N G

Toxic, flammable and hazardous solvents, samples and reagents

The handling of solvents, samples and reagents can hold health and safety risks.

➔

When working with these substances observe appropriate safety procedures (for 
example by wearing goggles, safety gloves and protective clothing) as described in 
the material handling and safety data sheet supplied by the vendor, and follow good 
laboratory practice.

➔

The volume of substances should be reduced to the minimum required for the 
analysis.

➔

Never exceed the maximal permissible volume of solvents (6 L) in the solvent 
cabinet.

➔

Do not use bottles that exceed the maximum permissible volume as specified in the 
usage guideline for the Agilent 1200 Infinity Series Solvent Cabinets.

➔

Arrange the bottles as specified in the usage guideline for the solvent cabinet.

➔

A printed copy of the guideline has been shipped with the solvent cabinet, 
electronic copies are available on the Internet.

N O T E

Recommendations for Solvent Cabinet

For details, see the usage guideline for the Agilent 1200 Infinity Series Solvent Cabinets.

Содержание G1314B

















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды