manualshive.com logo in svg

Agilent Technologies G1314B, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G1314B Скачать руководство пользователя страница 178

178

Agilent 1260 Infinity VWD User Manual

12

Hardware Information

Interfaces

Interfaces Overview

CAN

The CAN is inter- module communication interface. It is a 2- wire serial 
bus system supporting high speed data communication and real- time 
requirement.

LAN

The modules have either an interface slot for an LAN card (e.g. Agilent 
G1369B/C LAN Interface) or they have an on- board LAN interface (e.g. 
detectors G1315C/D DAD and G1365C/D MWD). This interface allows the 
control of the module/system via a PC with the appropriate control 
software. Some modules have neither on- board LAN nor an interface slot 
for a LAN card (e.g. G1170A Valve Drive or G4227A Flex Cube). These are 
hosted modules and require a Host module with firmware B.06.40 or later 
or with additional G1369C LAN Card. 

RS-232C (Serial)

The RS- 232C connector is used to control the module from a computer 
through RS- 232C connection, using the appropriate software. This 
connector can be configured with the configuration switch module at the 
rear of the module. Refer to 

Communication Settings for RS- 232C

.

The RS- 232C is designed as DCE (data communication equipment) with a 
9- pin male SUB- D type connector. The pins are defined as:

N O T E

If an Agilent detector (DAD/MWD/FLD/VWD/RID) is in the system, the LAN should be 
connected to the DAD/MWD/FLD/VWD/RID (due to higher data load). If no Agilent 
detector is part of the system, the LAN interface should be installed in the pump or 
autosampler.

N O T E

There is no configuration possible on main boards with on-board LAN. These are 
pre-configured for

•

19200 baud,

•

8 data bit with no parity and

•

one start bit and one stop bit are always used (not selectable).

Содержание G1314B

















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды