Agilent Technologies G1314B Скачать руководство пользователя страница 134

Страница: 134 / 208

134

Agilent 1260 Infinity VWD User Manual

Maintenance

Replacing the Interface Board

When

When defective or for installation of the board or for all repairs inside the detector.

Parts required

p/n

Description

G1351-68701

Interface board (BCD) with external contacts and BCD outputs

G1369B or
G1369-60002

Interface board (LAN)

G1369C or
G1369-60012

Interface board (LAN)

Install the ESD strap. Move the power lock across the
power inlet.

If required, unscrew and remove the interface board.
Place the board on the ESD kit.

Next Steps:

If required, insert the interface board and fix the screws.

Remove the ESD strap.

Reinstall the module into the stack.

:H9higVe

EdlZgadX`

Содержание G1314B

















































































































































































































Результаты поиска

Содержание G1314B

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies G1314B, Руководство пользователя

Результаты поиска

Содержание G1314B

Отзывы:

Бренды по названию

Популярные бренды